Winglets in Wind Tunnels


Objective

The goal of this project is to measure the changes in airfoil performance when winglets are added to the airfoil.

Introduction

Photo

The Boeing jet in the picture at right has winglets at the tips of its wings. Why are they there? What do they do?

As an airplane moves through the air, the wings generate lift by creating an area of low pressure above the upper surface of the wing. The higher air pressure beneath the lower surface of the wing lifts the plane. At the tip of the wing, the high and low pressure air meet.

Diagram of wing tip vortices from a passenger jet.
Figure 1. The diagram shows the expanding wing tip vortices generated by a passenger jet. (NASAexplores.com, date unknown)

The air forms miniature tornadoes, called wing tip vortices that spread out behind the plane (see Figure 1, right). Wing tip vortices cause two problems:

  1. the turbulent airflow they create can be strong enough to flip an airplane that encounters it;
  2. they also increase the drag forces on the airplane that generates them, decreasing fuel efficiency.
Winglets break up wing tip vortices, alleviating both of these problems.

The airflow around winglets is complex. Your wind tunnel should include smoke or fog in the airflow so that you can visualize streamlines along the length of the airfoil. Figure 2, below, illustrates some design considerations you may wish to consider for the winglets (Hepperle, 2006). A gradual curve transistioning from airfoil to winglet may help to reduce turbulent flow at the corner region. Translating the winglet toward the trailing edge of the airflow can also promote laminar flow at the trailing edge of the wingtip.

Three different winglet designs. From left to right: no winglet, rounded corner, sharp corner, winglet translated toward trailing edge.
Figure 2. Three different winglet designs. From left to right: no winglet, rounded corner, sharp corner, winglet translated toward trailing edge. (Hepperle, 2006)

In this project, you will test airfoils built both with and without winglets in a wind tunnel. Do you see evidence for wing tip vortices when testing airfoils without winglets? Does the addition of winglets alleviate wing tip vortices? Do the winglets increase lift? For winglet-related project ideas that do not require a wind tunnel, see the Variations section.

Terms, Concepts and Questions to Start Background Research

To do this project, you should do research that enables you to understand the following terms and concepts:

  • airfoil,
  • chord line,
  • mean camber line,
  • camber,
  • aspect ratio,
  • angle of attack,
  • winglets,
  • drag,
  • lift,
  • wing tip vortices.

Questions

  • What are the forces acting on an airfoil in a wind tunnel?
  • How will the addition of winglets affect these forces?
  • How will the addition of winglets affect flight performance?

Bibliography

Materials and Equipment

To do this experiment you will need the following materials and equipment:

  • materials for building model airfoils, e.g.:
    • balsa wood for framework,
    • tissue paper covering,
    • modeling knife,
    • glue,
    • airplane dope.
    • (Alternatively, airfoil sections can be shaped from solid pieces of balsa or other wood.)
  • wind tunnel for testing airfoils (See the Materials and Equipment section of the Aerodynamics & Hydrodynamics page for information on building your own wind tunnel: Wind Tunnel Construction Links.)

Experimental Procedure

  1. Do your background research so that you are knowledgeable about the terms, concepts, and questions above.
  2. Construct two or more airfoils, identical in shape except for the presence/absence of winglets. See Figure 2 in the Introduction for ideas on different winglet designs you might wish to consider.
  3. Test your airfoils in a wind tunnel. The measurements that you are able to make will depend on the instrumentation available. Desirable measurements are:
    1. lift,
    2. drag,
    3. visualization of streamlines at the wing tip (using smoke or fog).

Variations

  • For a much more basic project on winglets using paper airplanes, see the Science Buddies project Why Winglets?.
  • The simple folded airplanes used in the project just mentioned normally lack vertical stabilizers. Vertical stabilizers counteract imbalances in lift between the two wings, and thus resist forces that would tend to make the plane roll. In this simple type of paper airplane, winglets can function as vertical stabilizers. Another type of paper airplane (made with laminated construction methods) generally does include a vertical stabilizer as part of the design. For more details, see the Science Buddies project What Makes a Good Aerodynamic Design? Test Your Ideas with High-Performance Paper Gliders. Do winglets improve the flight characteristics of high-performance paper gliders?

Credits

Andrew Olson, Ph.D., Science Buddies


Last edit date: 2006-06-16 22:00:00

 

Copyright © 2002-2008 Kenneth Lafferty Hess Family Charitable Foundation. All rights reserved.
Reproduction of material from this website without written permission is strictly prohibited.
Use of this site constitutes acceptance of our Terms and Conditions of Fair Use.

Science Buddies gratefully acknowledges its Presenting Sponsor


Science Fair Project Home      Our Sponsors      About Us      Volunteer      Donate      Contact Us      Online Store      Privacy Policy      Image Credits      Site Map

Science Fair Project Ideas      Science Fair Project Guide      Ask an Expert      Teacher Resources      Science Fair Competitions