Jump to main content

How Far Will It Fly? Build & Test Paper Planes with Different Drag

1
2
3
4
5
3,178 reviews

Abstract

Just one sheet of paper can lead to a whole lot of fun. How? Paper planes! All you have to know is how to fold and you can have a simple plane in a matter of minutes! But what design should you use to build the best plane? In this aerodynamics science project, you will change the basic design of a paper plane and see how this affects its flight. Specifically, you will increase how much drag the plane experiences and see if this changes how far the paper plane flies. There is a lot of cool science in this project, such as how the different forces allow a plane to fly, so get ready to start folding!

Summary

Areas of Science
Difficulty
 
Time Required
Very Short (≤ 1 day)
Prerequisites
None
Material Availability
Readily available
Cost
Very Low (under $20)
Safety
Fly your planes in a large area, away from foot and vehicle traffic.
Credits

Michelle Maranowski, PhD, Science Buddies
Teisha Rowland, PhD, Science Buddies

Objective

Determine whether the distance a paper plane flies is affected by increasing how much drag it experiences.

Introduction

Paper airplanes are fun and easy to make. Just fold a piece of paper into a simple plane and send it soaring into the sky with a flick of your wrist. Watching it float and glide in the air gives you a very satisfying and happy feeling.

But what allows the paper plane to glide through the air? And why does a paper plane finally land? To find out, we will talk about the science behind flying a paper plane and the different forces that get a paper plane to fly and land. These same forces apply to real airplanes, too. A force is something that pushes or pulls on something else. When you throw a paper plane in the air, you are giving the plane a push to move forward. That push is a type of force called thrust. While the plane is flying forward, air is moving over and under the wings and is providing a force called lift to the plane. If the paper plane has enough thrust and the wings are properly designed, the plane will have a nice long flight.

But there is more than lack of thrust and poor wing design that gets a paper plane to come back to Earth. As a paper plane moves through the air, the air pushes against the plane, slowing it down. This force is called drag. To think about drag, imagine you are in a moving car and you put your hand outside of the window. The force of the air pushing your hand back as you move forward is drag. Finally, the weight of the paper plane affects its flight and brings it to a landing. Weight is the force of Earth's gravity acting on the paper plane. Figure 1 below shows how all four of these forces, thrust, lift, drag, and weight, act upon a paper plane.

A force diagram for a paper plane where it is acted on by thrust, lift, drag, and gravity

A paper airplane in flight will experience an initial thrust forward which begins its flight and lift from air which will help push it upward. These forces are counteracted by drag that acts in the opposite direction as thrust and gravity which will constantly pull the plane towards the ground.


Figure 1. When a paper plane is flying, the four forces of thrust, lift, drag, and weight are acting upon the plane, affecting how well its journey through the air goes.

Well, what do you think? Would you like to start experimenting with these forces? In this aerodynamics science project, you will make a basic paper plane and then slightly alter its shape to increase how much drag is acting on it. You will investigate how far the basic paper plane flies and compare that to how far it flies when the drag is increased. How will adding drag affect your plane's flight? You can answer this question with just a flick of your wrist.

Terms and Concepts

Questions

Bibliography

These sites explain how paper planes and airplanes fly.

  • Shaw, R. (2010, September 10). Dynamics of Flight. Retrieved November 24, 2010.
  • Doherty, P. (1999). Paper Airplanes. Exploratorium Magazine Online. Vol. 23, Number 2. Retrieved November 24, 2010.

The following resource can be used to convert inches and feet to metric units (i.e., centimeters and meters):

For help creating graphs, try this website:

  • National Center for Education Statistics, (n.d.). Create a Graph. Retrieved June 25, 2020.

Materials and Equipment

Experimental Procedure

Flying the Planes

  1. Follow the paper airplane template for the "intermediate" design instructions to build a paper airplane.
  2. Build two more so that you have a total of three paper planes. They should all look identical.
  3. Make a data table in your lab notebook, like Table 1 below, where you can record the data you get from your experiment.
Paper Plane Flight 1 Flight 2 Flight 3 Flight 4 Flight 5 Average
Plane 1            
Plane 1 with Added Drag            
Plane 2            
Plane 2 with Added Drag            
Plane 3            
Plane 3 with Added Drag            
Table 1. In your lab notebook, create a data table like this one. For each flight, write down how far the paper plane travels (in centimeters [cm] or meters [m]).
  1. Go to a large area to fly your paper plane. Make sure that there is no foot or car traffic at the area. A long hallway or your school gym is a good location. If you are flying your plane outside, like in a baseball field or on a basketball court, do your experiment on a day when there is no wind.
  2. Tear off a 5-foot-long piece of masking tape and tape it to the ground in front of you, going from left to right. This will be the starting line from which you will fly the paper planes. If you are doing this science project outside, you could use a line of sticks or rocks to mark the starting point.
  3. Practice throwing or launching the paper planes. You will want to launch the planes in exactly the same way every time. Hold the planes at exactly the same spot on the plane every time you launch a plane.
  4. Once you have finished practicing, it is time to start the experiment. Place your toe on the starting line you prepared earlier and then throw one of your planes.
  5. Use the tape measure to measure how far (in centimeters or meters) the paper plane flew from the starting line. Record this distance in the data table in your lab notebook.
    1. This will be "Flight 1" for "Plane 1."
    2. Science is done in metric units (e.g., centimeters and meters) so your data should be written as such. If your tape measure does not have metric units, you can convert inches or feet to centimeters or meters using this website:
      1. Science Made Simple, Inc. (n.d.). Length conversion using online length converter by Science Made Simple. Retrieved February 13, 2013.
  6. Repeat steps 7-8 four more times using the same plane, trying to throw the plane as similarly as possible. Doing these repeats will help ensure that your data is accurate and reproducible.
    1. Before you fly the plane, make sure that it is in good condition and that the folds and points are still sharp.
    2. Record the distances in the data table in your lab notebook all in the same row as "Plane 1," as "Flight 2," Flight 3," "Flight 4," or "Flight 5."
  7. Once you have flown plane 1 five times, add flaps to the back of the plane to increase its drag, as shown in Figure 2.
    1. Cut four slits that are each roughly 2.5 cm long along the back edge of the wings. One in the center of each wing, and one where each wing meets the central fold.
    2. This will result in four tabs (two on each wing). Fold two of the tabs up 90 degrees, and two of the tabs down 90 degrees, as shown in Figure 2.
    3. How do you think this increases the plane's drag?
Two paper planes with one plane having flaps added to the back of the wings
Figure 2. Left: the original plane. Right: a plane with flaps added to the back to increase drag.
  1. Using plane 1 with added drag, repeat steps 7-9.
    1. Record the distances the plane flies in your data table in the row titled "Plane 1 with Added Drag."
    2. In your lab notebook, record any observations about how this plane appears to fly compared to how plane 1 flew before you added drag.
  2. Repeat steps 10-11 using one of the other two planes you made.
    1. Record the distances the plane flies in the row titled "Plane 2" and then "Plane 2 with Added Drag."
    2. In your lab notebook, record any observations you make.
  3. Repeat steps 10-11 using the last of the three planes you made. (This plane should not have been flown previously.)
    1. Record the distances the plane flies in the row titled "Plane 3" and then "Plane 3 with Added Drag."
    2. In your lab notebook, record any observations you make.

Analyzing Your Data

  1. Using the data you collected in the data table in your lab notebook, calculate the average distance that each plane traveled, with and without added drag. Record your results in the column labeled "Average" in the data table.
    1. For example, if plane 1 traveled 4.60, 4.14, 5.00, 5.33, and 3.86 meters on flight 1, 2, 3, 4, and 5, respectively, to figure out its average distance you would first add these five distances together (which gives you 22.93 m) and then divide this number by five, which gives you an average distance of 4.59 meters.
  2. Use the data from your data table to create a bar graph.
    1. You can plot your data by hand or you can plot your data online at Create A Graph.
    2. Label the x-axis (the horizontal axis) "Paper Plane" and label the y-axis (the vertical axis) "Average Flight Distance." You will have six bars, one for each of the planes without added drag, and one for each of the planes with added drag. Make each bar go up to the average distance that plane traveled.
  3. What does your graph tell you? How did adding drag to your paper planes affect how far they flew?
    1. Can you explain your results in terms of how forces allow a plane to fly? Hint: Re-read the Introduction in the Background tab.
icon scientific method

Ask an Expert

Do you have specific questions about your science project? Our team of volunteer scientists can help. Our Experts won't do the work for you, but they will make suggestions, offer guidance, and help you troubleshoot.

Global Connections

The United Nations Sustainable Development Goals (UNSDGs) are a blueprint to achieve a better and more sustainable future for all.

This project explores topics key to Industry, Innovation and Infrastructure: Build resilient infrastructure, promote sustainable industrialization and foster innovation.

Variations

  • Does size matter? Make planes of different sizes but keep the design and the type of paper you use the same. Do bigger planes fly further?
  • Do more complicated planes fly further? In order words, does the number of folds that you use to make a paper plane affect the distance that it flies? Try this out using the same size and type of paper.
  • Does the type of paper you use affect how far the paper plane flies? Try making paper planes out of different types of paper, such as printer paper, construction paper, and newspaper. Make all of the planes using the same design and fly them as similarly as you can. Does one type of paper seem to work best for making paper planes? Does one type work the worst? You may need to do several trials to see a trend.
  • Some people like to add paperclips to their paper planes to make them fly better. But where should the paper clips be placed for the best flight? Try adding paperclips to the back, the front, the middle, or the wings. You can add one paper clip or several, but try to be consistent with how many you use. Take notes in your lab notebook so you know what you tested. Does adding paperclips somewhere make the paper plane's flight better, worse, or have no effect at all?

Careers

If you like this project, you might enjoy exploring these related careers:

Career Profile
Humans have always longed to fly and to make other things fly, both through the air and into outer space—aerospace engineers are the people that make those dreams come true. They design, build, and test vehicles like airplanes, helicopters, balloons, rockets, missiles, satellites, and spacecraft. Read more
Career Profile
Aerospace engineering and operations technicians are essential to the development of new aircraft and space vehicles. They build, test, and maintain parts for air and spacecraft, and assemble, test, and maintain the vehicles as well. They are key members of a flight readiness team, preparing space vehicles for launch in clean rooms, and on the launch pad. They also help troubleshoot launch or flight failures by testing suspect parts. Read more
Career Profile
Have you always loved art? Do you have a good eye for beauty, balance, and form? How would you like to see your designs show up in toy stores? Or in a sporting goods store? Or at a car dealer? Commercial and industrial designers create the shape and form of every type of manufactured good that you can think of—from toys, sporting goods, and medical equipment to high technology products, furniture, toothbrushes, and toasters. They design the form of new products that are as beautiful and… Read more
Career Profile
Aviation inspectors are critical to ensuring that aircraft are safe to fly. They conduct pre-flight inspections to make sure an aircraft is safe. They also inspect the work of aircraft mechanics, and keep detailed records of work done to maintain or repair an aircraft. As problems are identified, they may make changes to maintenance schedules, and may be called upon to investigate air accidents. Read more

News Feed on This Topic

 
, ,

Cite This Page

General citation information is provided here. Be sure to check the formatting, including capitalization, for the method you are using and update your citation, as needed.

MLA Style

Science Buddies Staff. "How Far Will It Fly? Build & Test Paper Planes with Different Drag." Science Buddies, 2 Feb. 2023, https://www.sciencebuddies.org/science-fair-projects/project-ideas/Aero_p046/aerodynamics-hydrodynamics/how-far-will-paper-planes-fly?from=Blog. Accessed 19 Mar. 2024.

APA Style

Science Buddies Staff. (2023, February 2). How Far Will It Fly? Build & Test Paper Planes with Different Drag. Retrieved from https://www.sciencebuddies.org/science-fair-projects/project-ideas/Aero_p046/aerodynamics-hydrodynamics/how-far-will-paper-planes-fly?from=Blog


Last edit date: 2023-02-02
Top
We use cookies and those of third party providers to deliver the best possible web experience and to compile statistics.
By continuing and using the site, including the landing page, you agree to our Privacy Policy and Terms of Use.
OK, got it
Free science fair projects.