Jump to main content

How Does the Intensity of Light Change with Distance?

1
2
3
4
5
188 reviews

Abstract

How does the intensity of a light source change as you move away from it? This project describes a method to verify the inverse square law: how light, sound, electrical signals, and gravity each decrease with distance from their source. It does not matter if you are talking about a lightbulb or the sun; this law still applies!

Summary

Areas of Science
Difficulty
 
Time Required
Very Short (≤ 1 day)
Prerequisites
None
Material Availability
A kit is available from our partner Home Science Tools. See the Materials section for details.
Cost
Average ($40 - $80)
Safety
No issues
Credits

Written by Richard Blish, PhD  AMD logo

Edited by Andrew Olson, PhD, and Ben Finio, PhD, Science Buddies

Thanks to David Aziz, PhD, for helpful suggestions on photocell measurement methods.

Recommended Project Supplies

Get the right supplies — selected and tested to work with this project.

View Kit

Objective

Determine how the intensity of light changes with increasing distance from the light source.

Introduction

As you move away from a light source, the light gets dimmer. No doubt you have noticed this with reading lamps, streetlights, and so on. Figure 1 shows what is happening. The blue area, marked "S," represents a point source of light. Imagine the light from the star spreading out into empty space in all directions. Now imagine the light that falls on a square at some arbitrary distance from the star (r). Move away, doubling the distance from the star (2r). The light from the original square has now "spread out" over an area of 4 (= 22) squares. Thus, at twice the original distance, the intensity (power per square meter) of the light passing through a single square will be 1/4 of the original intensity. Going out still farther, tripling the original distance (3r), and the light from the original square now covers an area of 9 (= 32) squares. Thus, at three times the original distance, the intensity of the light passing through a single square will be 1/9 of the original intensity. This is what is meant by the inverse square law. As you move away from a point light source, the intensity of the light is proportional to 1/r2, the inverse square of the distance. Because the same geometry applies to many other physical phenomena (sound, gravity, electrostatic interactions), the inverse square law has significance for many problems in physics.

Diagram uses a beam of light to illustrate the inverse square law

The figure shows directional light originating from a point source that covers a larger area the further away it is from the source. As the light travels it has a specific brightness and size at any given point. The inverse square law shows that when light travels twice the distance its area grows four times as large and the brightness decreases by four times. The rate a light grows in area and decreases in brightness is related to the distance it travels from another point squared.


Figure 1. An illustration of the inverse square law. Image credit Wikimedia Commons user Borb.

But do not just take our word for it! Why not see for yourself if light really behaves this way? This project shows you how you can use a light-sensitive resistor, called a photoresistor, which has an electrical resistance (measured in ohms (Ω)) that changes with exposure to light, and a digital multimeter to see if light intensity really does decrease according to the inverse square law. You will measure the resistance of the photoresistor at different distances from a light source. Using information from the photoresistor's datasheet, you can convert the resistance measurement to lux, the SI unit of illuminance (a measure of intensity that accounts for how different wavelengths are perceived by the human eye). You can then create a graph to see how illuminance changes with distance from the light source, and verify if it follows the inverse square law.

Terms and Concepts

To do this project, you should do research that enables you to understand the following terms and concepts:

Questions

Bibliography

Materials and Equipment Buy Kit

Recommended Project Supplies

Get the right supplies — selected and tested to work with this project.

View Kit

Disclaimer: Science Buddies participates in affiliate programs with Home Science Tools, Amazon.com, Carolina Biological, and Jameco Electronics. Proceeds from the affiliate programs help support Science Buddies, a 501(c)(3) public charity, and keep our resources free for everyone. Our top priority is student learning. If you have any comments (positive or negative) related to purchases you've made for science projects from recommendations on our site, please let us know. Write to us at scibuddy@sciencebuddies.org.

Experimental Procedure

  1. Set up your multimeter to measure the resistance of the photoresistor, as shown in Figure 2.
    1. Plug the black multimeter probe into the port labeled COM.
    2. Plug the red multimeter probe into the port labeled VΩmA.
    3. Connect the multimeter probes to the leads of the photoresistor using alligator clips.
    4. Set the multimeter dial to measure resistance in the 200 Ω range.
    5. Turn the multimeter's power switch to ON.
    6. If this is your first time using a multimeter, see the Science Buddies reference How to Use a Multimeter, particularly the section How do I measure resistance? to learn more.
Alligator clips connect the leads of a photoresistor to the probes of a multimeter
Figure 2. How to connect your multimeter to the photoresistor.
  1. Set up your experiment, as shown in Figure 3.
    1. If possible, set the experiment up in a room with no windows, or do the experiment at night. If this is not possible, find a room with as little external light as possible. The photoresistor is very sensitive; even a little bit of light leaking under a door can affect your readings.
    2. Turn off all other lights in the room except the single lamp you will use for the experiment.
    3. If necessary, remove the lamp shade from your lamp.
    4. Set up your tape measure to measure distance from the lamp.
    5. Tape your photoresistor to a cardboard box so it is level with the lamp. The face of the photoresistor (the side with the squiggly lines) should be facing directly toward the lamp.
A large lamp points towards a photoresistor that is connected to a multimeter
Figure 3. Experimental setup.
  1. Measure the resistance of the photoresistor as you increase the distance from the lightbulb (for example, every 10 cm).
    1. Take at least three readings at each distance and calculate an average.
    2. Try to take measurements over a range of at least several meters. If you have space, you can go even farther, but remember that stray ambient light will affect your readings.
    3. Note: The resistance will increase as you move away from the light source. If the screen of your multimeter reads "1 .", then the resistance has exceeded the range of the multimeter dial setting. Rotate the dial up one resistance setting (for example, from "200" to "2000") to increase the range. Make sure you pay attention to units. A prefix of "k" means "kilo-ohms" (kΩ).
  2. Convert the resistance values to illuminance in lux using Equation 1 (hold your mouse cursor over the equation to magnify it). Note: This equation is an approximation. See the Variations section to learn more about the source of Equation 1.
    Equation 1:
    where
    • E is the illuminance in lux
    • R is the resistance in kilo-ohms (so make sure to convert to kΩ before using Equation 1 if you took your readings in Ω)

  3. Make a graph of illuminance versus distance. Does the relationship follow the inverse square law? Advanced students should generate a best-fit curve and determine the R-squared value.
icon scientific method

Ask an Expert

Do you have specific questions about your science project? Our team of volunteer scientists can help. Our Experts won't do the work for you, but they will make suggestions, offer guidance, and help you troubleshoot.

Global Connections

The United Nations Sustainable Development Goals (UNSDGs) are a blueprint to achieve a better and more sustainable future for all.

This project explores topics key to Industry, Innovation and Infrastructure: Build resilient infrastructure, promote sustainable industrialization and foster innovation.

Variations

  • How does the resistance of the photoresistor change with distance? Make a plot of resistance versus distance. What is the mathematical relationship between resistance and distance? If you just glance at the graph, it might appear quadratic (resistance increases with distance squared), but is that actually the case?
  • Equation 1 is derived from the graph on the photoresistor's datasheet.
    • Can you derive Equation 1 yourself using the graph? This will require knowledge of log-log plots.
    • The graph only shows a calibration range for the sensor from 1–100 lux. The readings in your experiment may have exceeded this range. Can you be sure that the calibration curve is still linear (on a log-log plot) at higher or lower illuminance values? Use a lux meter to create your own calibration curve for the photoresistor over the range of illuminance values from your experiment. Does it match the graph from the datasheet? You can also do more research into the typical relationship between resistance and illuminance for photoresistors and examine the shape of the curve. What does this say about the validity of your results using Equation 1?
  • Do your results change if you do the experiment with different types of lightbulbs; for example, incandescent, compact fluorescent (CFL), or light-emitting diode (LED)? What about lightbulbs of different color temperature (for example "warm white" or "daylight"—look on the lightbulb's packaging to find the color temperature)? Does the wavelength of light emitted appear to have an effect on the inverse square law?

Careers

If you like this project, you might enjoy exploring these related careers:

Career Profile
You can send emails and text messages around the world in a matter of seconds. Surgeons routinely perform laser surgery that results in less bleeding and faster healing time. Our Air Force defends our skies using electronics-based aircraft that can almost fly themselves! What is one of the connections among these advances? Photonics technology! Photonics is the science of using light and electronic devices to create tools that improve our lives. Isn't it amazing that light can solve so many… Read more
Career Profile
Electricians are the people who bring electricity to our homes, schools, businesses, public spaces, and streets—lighting up our world, keeping the indoor temperature comfortable, and powering TVs, computers, and all sorts of machines that make life better. Electricians install and maintain the wiring and equipment that carries electricity, and they also fix electrical machines. Read more
Career Profile
Physicists have a big goal in mind—to understand the nature of the entire universe and everything in it! To reach that goal, they observe and measure natural events seen on Earth and in the universe, and then develop theories, using mathematics, to explain why those phenomena occur. Physicists take on the challenge of explaining events that happen on the grandest scale imaginable to those that happen at the level of the smallest atomic particles. Their theories are then applied to… Read more
Career Profile
Astronomers think big! They want to understand the entire universe—the nature of the Sun, Moon, planets, stars, galaxies, and everything in between. An astronomer's work can be pure science—gathering and analyzing data from instruments and creating theories about the nature of cosmic objects—or the work can be applied to practical problems in space flight and navigation, or satellite communications. Read more

Contact Us

If you have purchased a kit for this project from Science Buddies, we are pleased to answer your questions.

In your email, please follow these instructions:
  1. What is your Science Buddies kit order number?
  2. Please describe how you need help as thoroughly as possible:

    Examples

    Good Question I'm trying to do Experimental Procedure step #5, "Scrape the insulation from the wire. . ." How do I know when I've scraped enough?
    Good Question I'm at Experimental Procedure step #7, "Move the magnet back and forth . . ." and the LED is not lighting up.
    Bad Question I don't understand the instructions. Help!
    Good Question I am purchasing my materials. Can I substitute a 1N34 diode for the 1N25 diode called for in the material list?
    Bad Question Can I use a different part?

Contact Us

News Feed on This Topic

 
, ,

Cite This Page

General citation information is provided here. Be sure to check the formatting, including capitalization, for the method you are using and update your citation, as needed.

MLA Style

Science Buddies Staff. "How Does the Intensity of Light Change with Distance?" Science Buddies, 26 Oct. 2023, https://www.sciencebuddies.org/science-fair-projects/project-ideas/Elec_p028/electricity-electronics/measure-intensity-of-light?from=Home. Accessed 19 Mar. 2024.

APA Style

Science Buddies Staff. (2023, October 26). How Does the Intensity of Light Change with Distance? Retrieved from https://www.sciencebuddies.org/science-fair-projects/project-ideas/Elec_p028/electricity-electronics/measure-intensity-of-light?from=Home


Last edit date: 2023-10-26
Top
We use cookies and those of third party providers to deliver the best possible web experience and to compile statistics.
By continuing and using the site, including the landing page, you agree to our Privacy Policy and Terms of Use.
OK, got it
Free science fair projects.