Measuring the Surface Tension of Water
|Areas of Science||
|Time Required||Very Short (≤ 1 day)|
|Prerequisites||Basic physics: understanding of the concept of a force|
|Material Availability||Readily available|
|Cost||Very Low (under $20)|
AbstractDid you know that when you dip your finger in water and pull it out, the water is actually pulling back on you? Here's a way you can measure how much.
The goal of this project is to use a homemade single-beam balance to directly measure the surface tension of a liquid.
Gardner, R., 2004. Science Fair Projects About the Properties of Matter: Using Marbles, Water, Balloons, and More, Berkeley Heights, NJ: Enslow Publishers.
Calder, V. and D. Plano, 2002. "Measuring Surface Tension." Ask A Scientist Physics Archive, University of Chicago, Newton BBS. http://www.newton.dep.anl.gov/askasci/phy00/phy00455.htm.
Cite This PageGeneral citation information is provided here. Be sure to check the formatting, including capitalization, for the method you are using and update your citation, as needed.
Last edit date: 2018-03-14
You've seen examples of surface tension in action: water striders walking on water, soap bubbles, or perhaps water creeping up inside a thin tube. What, exactly, is surface tension?
Surface tension is defined as the amount of energy required to increase the surface area of a liquid by a unit amount. So the units can be expressed in joules per square meter (J/m2). You can also think of it as a force per unit length, pulling on an object (Mellendorf, 2002). In this case, the units would be in newtons/meter (N/m). Since the forces are so small, you often see surface tension expressed in millinewtons per meter (mN/m — 1 mN is 1/1000 N). It's a good exercise to do the dimensional analysis and prove that both ways of expressing surface tension—J/m2 and N/m—are equivalent.
The force arises from the mutual attraction between the molecules of the liquid. Do background research on the chemistry of water to learn more about its intermolecular attractions. In particular, you should study up on hydrogen bonding.
In this experiment, you will be making and using a single beam balance to measure the force exerted by surface tension on a needle, floating on the surface of the water. The needle will be attached to your balance, and you will measure how much force is required to pull the needle out of the water. The surface tension of the water is providing the resistance. From your measurements, you will be able to calculate the surface tension of water.
Terms and ConceptsTo do this project, you should do research that enables you to understand the following terms and concepts:
- surface tension,
- water molecules,
- hydrogen bonding of water molecules,
- Considering what you have learned about hydrogen bonding in your background research:
- will adding detergent to water increase or decrease the surface tension?
- will adding rubbing alcohol to water increase or decrease the surface tension?
- Agrawal, A. (n.d.). Fundamentals of Surface Tension/Wettability. Massachusetts Institute of Technology: Non-Newtonian Fluid Dynamics Research Group. Retrieved March 24, 2014, from http://web.mit.edu/nnf/education/wettability/index1.html
- Rader, A. (n.d.). Motion Basics: Gravity. Physics4Kids.com. Retrieved March 24, 2014, from http://www.physics4kids.com/files/motion_gravity.html
- This is an archive of a physics discussion board with information on measuring surface tension:
Calder, V. and Plano, D. (2002). Measuring Surface Tension. Ask a Scientist Physics Archive, University of Chicago, Newton BBS. Retrieved March 24, 2014, from http://www.newton.dep.anl.gov/askasci/phy00/phy00455.htm
- This is an archive of a physics discussion board with information on surface tension units:
Calder, V., Mellendorf, K., and Plano, D. (2003). Surface Tension Units. Ask a Scientist Physics Archive, University of Chicago, Newton BBS. Retrieved March 24, 2014, from http://www.newton.dep.anl.gov/askasci/phy00/phy00656.htm
- A great book with lots of project ideas on the properties of matter:
Gardner, R. (2004). Science Fair Projects About the Properties of Matter: Using Marbles, Water, Balloons, and More. Berkeley Heights, NJ: Enslow Publishers.
News Feed on This Topic
Materials and EquipmentTo construct a homemade single-beam balance (see Figure 1 in the Experimental Procedure section), you will need the following:
- a beam (e.g., drinking straw, piece of stiff cardboard, wooden or plastic ruler),
- a fulcrum (e.g., a pin or nail),
- 2 supports of equal height (e.g., two books arranged back-to-back with a small space between them, two cans, two wood blocks),
- pan for weights (you can make this from foil),
- needle (or 5 cm length of straightened paper clip wire),
- thread (for attaching pan and needle to balance),
- small bit of modeling clay to counterbalance the empty pan.
- a small bowl,
- liquid detergent,
- plus any other liquids whose surface tension you would like to measure (e.g., rubbing alcohol, cooking oil).
- metric ruler
- weights (common pins, drops of water from an eyedropper),
- and a way to calibrate them (self-service scale at post office, 10 ml graduated cylinder).
- Do your background research.
- Gather the materials and find a good place to work.
- Constructing the balance (refer to Figure 1).
- Take your time and work carefully. You'll get better results.
- First construct the beam.
- There are many choices for materials. You just need something stiff enough to support a few grams at each end.
- You'll need to mark the center point for the fulcrum. Depending on your choice of material, either drill a hole for the fulcrum (e.g., for wood), or simply push it through (e.g., pin through a drinking straw). The beam needs to rotate freely about the fulcrum.
- You'll also need to make holes at each end of the beam, equidistant from the center. Attach loops of thread through the holes (paper clips, or ornament hangers could also work), as shown.
- Push the fulcrum through the center hole of the beam, and place it on the supports.
- Next construct the pan.
- This can be a simple box or dish folded from aluminum foil. (It's square in the diagram only because it was easier to draw.)
- If you make a round pan, three strings will work fine for supporting it.
- Tie a thread to the center of your needle or paperclip wire. Adjust the thread so that the needle or wire hangs horizontally.
- Measuring surface tension.
- Hang the pan from one end of the beam and the needle from the other, as shown in Figure 1. Use a small piece of modeling clay as a counterbalance (as shown in Figure 1) to balance the needle and empty pan.
- Fill the container that the needle will go in with water. Put the container under the needle.
- Place your container of water so that the needle (or wire), still hanging horizontally, is resting just on the surface of the water. Make sure the string holding the needle is taut (shorten it if necessary, to match the height of your balance's supports).
- You will add small amounts of weight to the pan, and measure the force needed to pull the needle (or wire) free from the surface of the water.
- It will not take much weight, so you need to add it in small increments. Here are two different methods you could try.
- Use common pins as your weights, adding them one at a time. Calibrate them by weighing a bunch of pins on a postal scale, and dividing by the number of pins to get the weight per pin.
- Use drops of water from an eyedropper or plastic transfer pipette. You can calibrate the water drops by counting how many drops are needed to make, say, 5 ml. Each milliliter of water weighs 1 g, so with your count you can calculate how much each drop weighs.
- Try both methods and see how your results compare!
- Make sure you record which method(s) you used, and how many pins or drops of water it took to completely remove the needle from the water.
- Repeat the measurement (steps 4.a–4.d) at least five times (more is better), to ensure consistent results. If something goes wrong (e.g., you accidentally tap the pan and pull the needle out of the water), repeat the trial from the beginning.
- Average your results.
- The force you will be measuring can be expressed by the equation:
F = 2sd, where
- F is the force, in newtons (N),
- the factor of 2 is because the film of water pulled up by the needle (or wire) has 2 surfaces,
- s is the surface tension per unit length, in units of newtons/meter (N/m), and
- d is the length of the needle (or wire), in units of meters (m).
- To convert grams to the force, F, you have to account for gravity pulling down on the mass in the pan. Calculate the total mass in the pan by multiplying the number of pins (or drops of water) by the mass of a single pin (or drop of water), which you calculated in step 4.d. Then multiply the total mass (in grams) by 9.81×10-3 N/g (for more information, see the reference about gravitational force in the Bibliography).
- You can rearrange the equation above to solve for s, the surface tension of water. Measure the length of the needle (or wire), and you'll have all the information you need to calculate the surface tension of water.
- How do you know that you are measuring surface tension, and not an attractive force between the needle (or wire) and the water? Here's a good tip from Robert Gardner's book (Gardner, 2004). Surface tension is the cohesive force between water molecules. Observe the needle (or wire) carefully after it is pulled out of the water. If it remains wet, then it must be the water that pulled apart, and this is the force (surface tension) that you measured. If it is dry, then the adhesive force between the water and the needle broke first, and this is what you measured, not surface tension.
If you like this project, you might enjoy exploring these related careers:
- Add a drop of liquid dish detergent to the water in your dish, mix it by stirring gently (you don't want a lot of bubbles), and measure the surface tension again. Do you think it will be higher or lower than for plain tap water?
- Try measuring the surface tension of other liquids, (e.g., rubbing alcohol, cooking oil). Remember note 2j, in the Experimental Procedure section.
- For another method of investigating surface tension, see: Build a Motorboat Powered by Surface Tension.
- For a project on the chemistry of surface tension, see: Measuring Surface Tension of Water with a Penny.
Ask an ExpertThe Ask an Expert Forum is intended to be a place where students can go to find answers to science questions that they have been unable to find using other resources. If you have specific questions about your science fair project or science fair, our team of volunteer scientists can help. Our Experts won't do the work for you, but they will make suggestions, offer guidance, and help you troubleshoot.
Ask an Expert
News Feed on This Topic
Looking for more science fun?
Try one of our science activities for quick, anytime science explorations. The perfect thing to liven up a rainy day, school vacation, or moment of boredom.Find an Activity
Explore Our Science Videos
Flower Dissection - STEM Activity
Solubility Science - STEM Activity
Make a Hygrometer to Measure Humidity - STEM activity