Jump to main content
Science Projects

Measuring the Surface Tension of Water

1
2
3
4
5
660 reviews
Log In

This feature requires that you be logged in as a Google Classroom teacher and that you have an active class in Google Classroom.

If you are a Google Classroom teacher, please log in now.

For additional information about using Science Buddies with Google Classroom, see our FAQ.

Abstract

Did you know that when you dip your finger in water and pull it out, the water is actually pulling back on you? Here's a way you can measure how much.

Summary

Areas of Science
Physics
Difficulty
 
Time Required
Very Short (≤ 1 day)
Prerequisites
Basic physics: understanding of the concept of a force
Material Availability
Readily available
Cost
Very Low (under $20)
Safety
No issues
Credits
Andrew Olson, Ph.D., Science Buddies
Gardner, R., 2004. Science Fair Projects About the Properties of Matter: Using Marbles, Water, Balloons, and More, Berkeley Heights, NJ: Enslow Publishers.
Calder, V. and D. Plano, 2002. Measuring Surface Tension. Ask A Scientist Physics Archive, University of Chicago, Newton BBS.

Objective

The goal of this project is to use a homemade single-beam balance to directly measure the surface tension of a liquid.

Introduction

You've seen examples of surface tension in action: water striders walking on water, soap bubbles, or perhaps water creeping up inside a thin tube. What, exactly, is surface tension?

Surface tension is defined as the amount of energy required to increase the surface area of a liquid by a unit amount. So the units can be expressed in joules per square meter (J/m2). You can also think of it as a force per unit length, pulling on an object (Mellendorf, 2002). In this case, the units would be in newtons/meter (N/m). Since the forces are so small, you often see surface tension expressed in millinewtons per meter (mN/m — 1 mN is 1/1000 N). It's a good exercise to do the dimensional analysis and prove that both ways of expressing surface tension—J/m2 and N/m—are equivalent.

The force arises from the mutual attraction between the molecules of the liquid. Do background research on the chemistry of water to learn more about its intermolecular attractions. In particular, you should study up on hydrogen bonding.

In this experiment, you will be making and using a single beam balance to measure the force exerted by surface tension on a needle, floating on the surface of the water. The needle will be attached to your balance, and you will measure how much force is required to pull the needle out of the water. The surface tension of the water is providing the resistance. From your measurements, you will be able to calculate the surface tension of water.

Terms and Concepts

To do this project, you should do research that enables you to understand the following terms and concepts:

Questions

Considering what you have learned about hydrogen bonding in your background research:

Bibliography

  • Agrawal, A. (n.d.). Fundamentals of Surface Tension/Wettability. Massachusetts Institute of Technology: Non-Newtonian Fluid Dynamics Research Group. Retrieved March 24, 2014.
  • Rader, A. (n.d.). Motion Basics: Gravity. Physics4Kids.com. Retrieved March 24, 2014.
  • This is an archive of a physics discussion board with information on measuring surface tension:
    Calder, V. and Plano, D. (2002). Measuring Surface Tension. Ask a Scientist Physics Archive, University of Chicago, Newton BBS. Retrieved March 24, 2014.
  • This is an archive of a physics discussion board with information on surface tension units:
    Calder, V., Mellendorf, K., and Plano, D. (2003). Surface Tension Units. Ask a Scientist Physics Archive, University of Chicago, Newton BBS. Retrieved March 24, 2014.
  • A great book with lots of project ideas on the properties of matter:
    Gardner, R. (2004). Science Fair Projects About the Properties of Matter: Using Marbles, Water, Balloons, and More. Berkeley Heights, NJ: Enslow Publishers.

Materials and Equipment

To construct a homemade single-beam balance (see Figure 1 in the Experimental Procedure section), you will need the following: You will also need:

Experimental Procedure

  1. Do your background research.
  2. Gather the materials and find a good place to work.
    Diagram of a single-beam balance remaining level with different sized weights on each end
    Figure 1. Diagram of a simple single-beam balance
  3. Constructing the balance (refer to Figure 1).
    1. Take your time and work carefully. You'll get better results.
    2. Make a support. Figure 2 shows an example.

      Front and side view of two small containers of modeling clay holding wide craft sticks upright. A skewer pokes through the craft sticks, making a horizontal bar. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
      Figure 2. Side and front view of the support structure that will hold the balance beam up.
    3. Construct the balance beam.
      1. There are many choices for materials. You just need something stiff enough to support a few grams at each end.
      2. You will need to mark the center point for the fulcrum. Depending on your choice of material, either drill a hole for the fulcrum (e.g., for wood), or simply push it through (e.g., a skewer through a drinking straw, as shown in Figure 3). The beam needs to rotate freely about the fulcrum.

        A straw with a ruler next to it. A skewer poked a hole through the straw in the middle. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
        Figure 3. A black straw is perforated In the middle to serve as a balance beam.
      3. You'll also need to make holes at each end of the balance beam, equidistant from the center. Attach loops of thread through the holes (paper clips, or ornament hangers could also work), as shown in Figure 4.
      4. Push the fulcrum through the center hole of the beam, and place it on the supports as shown in Figure 1, or thread it through the support as shown in Figure 2.


      A black straw with perforations in the center and near the end. The center perforation is labeled 'fulcrum'. Paperclips are attached at both ends of the straw, equidistant from the fulcrum. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
      Figure 4. The balance beam is perforated near the middle and at equidistant ends from the fulcrum.
    4. Construct the pan.
      1. This can be a simple box or dish folded from aluminum foil or other material. (It's square in the diagram only because it was easier to draw.)
      2. If you make a round pan, three strings will work fine to support it.
      3. Use a water-resistant material or coat the pan with tape or water-repellent paint.


      A basket folded from paper coated with tape. Four string hang the basket from a metal hook. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
      Figure 5. Basket or pan to hold drops of water or pins.
    5. Tie a thread to the center of your needle or paperclip wire. Adjust the thread so that the needle or wire hangs horizontally. The pictures show a thicker string so the string would be visible. For your project, it is better to use thread instead.
  4. Measuring surface tension.
    1. Hang the pan from one end of the beam and the needle from the other, as shown in Figure 1 or Figure 6.

      the balance beam with a basket attached on one side and a needle on a string on the other side. The beam tips over as the basket is heavier than the needle. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
      Figure 6. The balance beam with the needle and basket attached. Because the basket is heavier, the balance beam tilts to one side.
    2. Use a small piece of modeling clay as a counterbalance (as shown in Figure 1 or Figure 7) to balance the needle and empty pan.

      the surface tension instrument with the beam balanced because of a small piece of modeling clay that was added to the needle side of the beam. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
      Figure 7. The balance beam is balanced by adding a small piece of blue modeling clay on the lighter end.
    3. Fill the container that the needle will go in with water. Put the container under the needle. You might need to make a platform to put your container with water on so the needle just dips into the water while the string stays taut, as shown in Figure 8.

      The balance beam is still horizontal, but the needle rests just on top of the water surface with the wire stretched. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
      Figure 8. An instrument to measure surface tension.
    4. Place your container of water so that the needle (or wire), still hanging horizontally, is resting just on the surface of the water. Make sure the string holding the needle is taut (shorten it if necessary).
    5. You will add small amounts of weight to the pan, and measure the force needed to pull the needle (or wire) free from the surface of the water. The beam will tip as soon as the needle breaks free, as shown in Figure 9.

      the surface tension measurement tool with the beam tipped over so the needle hangs in the air, far above the surface of the water. Image Credit: Sabine De Brabandere, Science Buddies / Science Buddies
      Figure 9. As soon as the surface of the water breaks, the beam tips.
    6. It will not take much weight, so you need to add it in small increments. Here are two different methods you could try.
      1. Use common pins as your weights, adding them one at a time. Calibrate them by weighing a bunch of pins on a postal scale, and dividing by the number of pins to get the weight per pin.
      2. Use drops of water from an eyedropper or plastic transfer pipette. You can calibrate the water drops by counting how many drops are needed to make, say, 5 ml. Each milliliter of water weighs 1 g, so with your count you can calculate how much each drop weighs.
      3. Try both methods and see how your results compare!
      4. Make sure you record which method(s) you used, and how many pins or drops of water it took to completely remove the needle from the water. A table like Table 1 can help collect the data.

      Weight needed to break the surface tension

      Length of needle: ______meter.
        Trail 1Trail 2Trail 3Trail 4Trail 5 Average
      Drops of water       
      Pins       
      Table 1. Example table to collect experimental data.
    7. Repeat the measurement (steps 4.a-4.e) at least five times (more is better), to ensure consistent results. If something goes wrong (e.g., you accidentally tap the pan and pull the needle out of the water), repeat the trial from the beginning.
    8. Average your results.
    9. The force you will be measuring can be expressed by the equation: F = 2sd, where
      • F is the force, in newtons (N),
      • the factor of 2 is because the film of water pulled up by the needle (or wire) has 2 surfaces,
      • s is the surface tension per unit length, in units of newtons/meter (N/m), and
      • d is the length of the needle (or wire), in units of meters (m).
    10. To convert grams to the force, F, you have to account for gravity pulling down on the mass in the pan. Calculate the total mass in the pan by multiplying the number of pins (or drops of water) by the mass of a single pin (or drop of water), which you calculated in step 4.f. Then multiply the total mass (in grams) by 9.81×10-3 N/g or 9.81/1000 N/g (for more information, see the reference about gravitational force in the Bibliography).
    11. You can rearrange the equation above to solve for s, the surface tension of water. Measure the length of the needle (or wire), and you'll have all the information you need to calculate the surface tension of water.
    12. How do you know that you are measuring surface tension, and not an attractive force between the needle (or wire) and the water? Here's a good tip from Robert Gardner's book (Gardner, 2004). Surface tension is the cohesive force between water molecules. Observe the needle (or wire) carefully after it is pulled out of the water. If it remains wet, then it must be the water that pulled apart, and this is the force (surface tension) that you measured. If it is dry, then the adhesive force between the water and the needle broke first, and this is what you measured, not surface tension.
icon scientific method

Ask an Expert

Do you have specific questions about your science project? Our team of volunteer scientists can help. Our Experts won't do the work for you, but they will make suggestions, offer guidance, and help you troubleshoot.
Post a Question

Variations

  • Add a drop of liquid dish detergent to the water in your dish, mix it by stirring gently (you don't want a lot of bubbles), and measure the surface tension again. Do you think it will be higher or lower than for plain tap water?
  • Try measuring the surface tension of other liquids, (e.g., rubbing alcohol, cooking oil). Remember note 2j, in the Experimental Procedure section.
  • For another method of investigating surface tension, see: Build a Motorboat Powered by Surface Tension.
  • For a project on the chemistry of surface tension, see: Measuring Surface Tension of Water with a Penny.

Careers

If you like this project, you might enjoy exploring these related careers:

Mechanical Engineer
Log in to add favorite
Career Profile
Mechanical engineers are part of your everyday life, designing the spoon you used to eat your breakfast, your breakfast's packaging, the flip-top cap on your toothpaste tube, the zipper on your jacket, the car, bike, or bus you took to school, the chair you sat in, the door handle you grasped and the hinges it opened on, and the ballpoint pen you used to take your test. Virtually every object that you see around you has passed through the hands of a mechanical engineer. Consequently, their… Read more
Precision Instrument & Equipment Repairer
Log in to add favorite
Career Profile
One of the basic truths in the universe is that objects tend to go from a state of higher organization to a state of lower organization over time. In other words, things break down, and when those things are precision instruments or equipment, they require the services of very specialized technicians to restore them to their working order. Precision instrument or equipment technicians often combine a love of music, medicine, electronics, or antiques with delicate mechanical repair work. Read more
Physicist
Log in to add favorite
Career Profile
Physicists have a big goal in mind—to understand the nature of the entire universe and everything in it! To reach that goal, they observe and measure natural events seen on Earth and in the universe, and then develop theories, using mathematics, to explain why those phenomena occur. Physicists take on the challenge of explaining events that happen on the grandest scale imaginable to those that happen at the level of the smallest atomic particles. Their theories are then applied to… Read more
Mechanical Engineering Technician
Log in to add favorite
Career Profile
You use mechanical devices every day—to zip and snap your clothing, open doors, refrigerate and cook your food, get clean water, heat your home, play music, surf the Internet, travel around, and even to brush your teeth. Virtually every object that you see around has been mechanically engineered or designed at some point, requiring the skills of mechanical engineering technicians to create drawings of the product, or to build and test models of the product to find the best design. Read more

News Feed on This Topic

 
, ,

Cite This Page

General citation information is provided here. Be sure to check the formatting, including capitalization, for the method you are using and update your citation, as needed.

MLA Style

Science Buddies Staff. "Measuring the Surface Tension of Water." Science Buddies, 18 Jan. 2022, https://www.sciencebuddies.org/science-fair-projects/project-ideas/Phys_p012/physics/measuring-the-surface-tension-of-water?class=AQXO-yu5qozGZvLTcGOFHO2FxJvFt0wh2aw05HAya5eCp2dzm_bSNvGP5xOSuGwgbykXZ3MU6TL1dhRhfIcmVTsW59zf8t8yUTbLU0CSPvSMDA. Accessed 19 Apr. 2024.

APA Style

Science Buddies Staff. (2022, January 18). Measuring the Surface Tension of Water. Retrieved from https://www.sciencebuddies.org/science-fair-projects/project-ideas/Phys_p012/physics/measuring-the-surface-tension-of-water?class=AQXO-yu5qozGZvLTcGOFHO2FxJvFt0wh2aw05HAya5eCp2dzm_bSNvGP5xOSuGwgbykXZ3MU6TL1dhRhfIcmVTsW59zf8t8yUTbLU0CSPvSMDA


Last edit date: 2022-01-18

Explore Our Science Videos

The Impossible Arrow Illusion
Is the Egg Raw or Cooked? STEM activity
Build a Mini Trebuchet
Quick Links X
Top
Free science fair projects.