Using Weather Balloon Data to Map Atmospheric Temperature
|Areas of Science||
Weather & Atmosphere
|Time Required||Average (6-10 days)|
|Material Availability||Readily available|
|Cost||Very Low (under $20)|
AbstractSnow-capped mountains make a picturesque scene, especially in summertime when the peaks are in such contrast to the warmth below. This project shows you a way to see how temperature changes with altitude using data collected twice daily from weather balloons.
ObjectiveThe goal of this project is to use weather balloon sounding data to investigate how air temperature and pressure vary with altitude.
SourcesThis project is based on:
- Millersville University LEAD Undergraduates, n.d. Lead-to-Learn: Exploring Temperature and Pressure Changes with Altitude Millersville University. Retrieved March 27, 2007.
Cite This PageGeneral citation information is provided here. Be sure to check the formatting, including capitalization, for the method you are using and update your citation, as needed.
Last edit date: 2020-07-08
Twice a day all over the U.S., the National Weather Service launches weather balloons with instrumentation packages called radiosondes to collect data on the current conditions of the upper atmosphere. As they ascend with the weather balloon, the radiosondes measure profiles of pressure, temperature, and relative humidity. The radiosondes contain radio transmitters that send the collected data back to Earth. The data are used for weather forecasting, and are available online.
You can use this data for a science fair project on atmospheric conditions. We will show you how to read temperature and pressure data from a standard upper air sounding plot—the same graphs that are used by meteorologists for weather forecasting. This project shows you how to find out how the temperature changes with altitude in the lowest layer of the Earth's atmosphere, the troposphere.
Figure 1 shows an example of an upper air sounding plot. This is a standard graph used by meteorologists to analyze data from a balloon sounding. There is a lot of additional information in the graph, but basically it is a plot of temperature (x-axis) vs. height (y-axis). The white data line on the left shows the dewpoint vs. pressure, and the white data line on the right shows the temperature vs. pressure. The pressure (in millibars, mb) is shown on the y-axis in blue lettering, and the height (in m) is shown in white lettering. A sounding plot is also called a "Skew T" plot, because the temperature axis is plotted at an angle (i.e., skew) of 45°. The temperature lines of the Skew T are in blue (at 45°).
A screenshot of an upper air sounding plot with data shown from International Falls, Minnesota on March 23, 2007. Dewpoint and temperature of the atmosphere are plotted with elevation on the left axis, temperature along the x-axis, and wind speed on the right.
Figure 1. Example of an upper air sounding plot from the Unisys Weather webpage. Data shown are from International Falls, MN, March 23, 2007. Brrrrr!
Atmospheric pressure decreases with height above the Earth's surface. The higher you go, the less atmosphere remains above you, so the pressure decreases. "Meteorology uses pressure as the vertical coordinate and not height. This works out better for thermodynamic computations that are done on a regular basis. Pressure decreases in the atmosphere exponentially as height increases reaching 0 pressure in space. The standard unit of pressure is millibars (mb or hectopascals-hPa) of which sea level is around 1015 mb. Here is a table of pressure levels and approximate heights (Unisys Corp., 2001):"
|Pressure||Approximate Height||Approximate Temperature|
Figure 2 shows how to read the temperature at a chosen pressure level (height). On the y-axis, find the pressure level (in mb) where you want to know the temperature. Follow the horizontal pressure line over until it intersects with the temperature plot (right-hand data plot, in white). Then follow the 45° temperature line down and to the left to the temperature axis. As shown in Figure 2, the temperature at 700 mb was about −11°C.
A screenshot of an upper air sounding plot with data shown from International Falls, Minnesota on March 23, 2007. The plot includes instructions to calculate the temperature at a given altitude and pressure level. To find the temperature at a given pressure level, read straight across the temperature plot, and then follow the blue lines down to the left to find the corresponding temperature.
Figure 2. Reading the temperature of the atmosphere at 700 mb (3022 m) from the sounding plot. Follow the horizontal pressure line to where it intersects with the temperature plot (right hand data line, in white). Then follow the 45° temperature line down and to the left to the temperature axis. In this example, the temperature at 700 mb was about -11°C.
There is a lot more information in the sounding plot, but it isn't important for this project. If you want to learn more about sounding plots, do more research about them online.
In this project you will use balloon sounding data to investigate how atmospheric temperature and pressure change with altitude.
Terms and ConceptsTo do this project, you should do research that enables you to understand the following terms and concepts:
- What is the source of heat for the troposphere?
- For more information about the layers of the Earth's atmosphere, see:
- UCAR, 2000. Windows to the Universe: Layers of the Earth's Atmosphere, University Corporation for Atmospheric Research. Retrieved March 27, 2007.
- University of Tennessee, date unknown. The Solar System: The Earth's Atmosphere, Astronomy 161, Department of Physics and Astronomy, University of Tennessee, Knoxville. Retrieved March 27, 2007.
- For current and archived sounding plots, see:
NOAA Storm Prediction Center (n.d.). Observed Sounding Archive. National Oceanic and Atmospheric Administration. Retrieved January 1, 2019.
News Feed on This Topic
Materials and EquipmentTo do this experiment you will need the following materials and equipment:
- Computer with Internet access
- Graph paper or graphing software
- Do your background research so that you are knowledgeable about the terms, concepts, and questions.
- For current weather balloon data from across the U.S., you will need to find sounding plots online, for example from https://www.spc.noaa.gov/exper/soundings/.
- Follow the instructions in the Introduction for reading the sounding plot. Make a table showing pressure (in mb), altitude (in m), and temperature (in °C) for each of the pressure levels shown in the sounding plot.
- Repeat this for at least 5 different sounding stations.
- Make a graph of your results that shows how temperature varies with atmospheric pressure for each station.
- Make a graph of your results that shows how pressure varies with altitude for each station.
If you like this project, you might enjoy exploring these related careers:
- Balloon soundings are taken at 12-hour intervals. (Notice that the time given in the plots is coordinated universal time (UCT), not local time.) Depending on the station location and time of year, you may be able to compare soundings taken during daylight hours to those taken after sundown. Compare several sequential pairs of soundings (daylight/after sundown) for several locations. Do you see any consistent relationships in the two temperature plots? What do they tell you about the sun's contribution to heating different levels of the atmosphere?
- For an experiment that relates atmospheric temperature and characteristics of snow, see the Science Buddies project How Does Atmospheric Temperature Affect the Water Content of Snow?
Ask an ExpertThe Ask an Expert Forum is intended to be a place where students can go to find answers to science questions that they have been unable to find using other resources. If you have specific questions about your science fair project or science fair, our team of volunteer scientists can help. Our Experts won't do the work for you, but they will make suggestions, offer guidance, and help you troubleshoot.
Ask an Expert
News Feed on This Topic
Looking for more science fun?
Try one of our science activities for quick, anytime science explorations. The perfect thing to liven up a rainy day, school vacation, or moment of boredom.Find an Activity
Explore Our Science Videos
BlueBot 4-in-1 Robotics Kit
Slippery Slopes - STEM activity
Gel Electrophoresis and Forensic Science: Biotechnology Science Fair Project