# Build a Marble Roller Coaster

1
2
3
4
5
25 reviews

## Summary

Active Time
10-20 minutes
Total Project Time
10-20 minutes
Key Concepts
Gravity, potential energy, kinetic energy
Credits
Ben Finio, PhD, Science Buddies

## Introduction

How much energy does a roller coaster need to go through a loop without getting stuck? Build your own marble roller coaster in this project and find out!

This activity is not recommended for use as a science fair project. Good science fair projects have a stronger focus on controlling variables, taking accurate measurements, and analyzing data. To find a science fair project that is just right for you, browse our library of over 1,200 Science Fair Project Ideas or use the Topic Selection Wizard to get a personalized project recommendation.

## Materials

• 1.5" diameter foam pipe insulation (at least one 6-foot section)
• Glass marbles or metal ball bearings
• Painter's tape
• Utility knife
• Table or chair

## Prep Work

Ask an adult to use the utility knife to cut the pipe insulation in half lengthwise, forming two U-shaped channels.

## Instructions

1. Curl one end of a piece of pipe insulation into a loop, roughly 1 foot in diameter.
2. Tape the loop to the floor to hold it in place. Make sure tape is not blocking the inside of the channel (it's OK to tape have tape on the inside, just make sure it is pressed flat and will not block the marble).
3. Tape the free end of the pipe insulation to a table or chair, forming a large hill leading down to the loop.
4. Place your marble a few inches from the bottom of the hill and release it. Does the marble make it through the loop?
5. Move your marble a few inches up the track and release it again. Keep repeating this process until the marble goes the whole way through the loop.
 How high does the starting position need to be before the marble goes through the loop? Is it lower, the same height, or higher than the top of the loop?
6. Expand your coaster! Try adding twists, turns, hills, or more loops. You can make your coaster even taller by taping pieces of pipe insulation together end-to-end. How high do you need to start the marble for it to make it to the end of your coaster?

## What Happened?

You should have discovered the marble needed to start higher than the top of the loop in order to make it the whole way through the loop. Read the Digging Deeper section to learn why!

## Digging Deeper

Roller coasters rely on two types of energy to operate: gravitational potential energy and kinetic energy. Gravitational potential energy* is the energy an object has stored due to its mass and its height off the ground. Kinetic energy is the energy an object has due to its mass and its velocity.

When a roller coaster reaches the very top of its initial hill, it has a lot of potential energy because it is very high off the ground. It moves over the top of the hill very slowly, so it has almost no kinetic energy. Then, it drops down the other side of the hill, and starts going very fast as its height rapidly decreases. The potential energy is converted to kinetic energy. This process repeats as the coaster goes through hills, loops, twists, and turns. Whenever it goes up, it gains more potential energy, but loses kinetic energy as it slows down. Energy is never created or destroyed—it just converts from one form to another. This is known as conservation of energy.

However, we know from experience that a roller coaster can't keep going forever. Eventually it slows down because of friction (a combination of air resistance and friction with the track). If energy isn't created or destroyed, where does that energy go? It is converted into heat. This is why you can rub your hands together to warm them up — friction converts energy from your moving hands into heat!

Because of friction, your marble will always need to start slightly higher than the very top of the loop. Otherwise, it will never have enough energy to make it through the loop without stopping.

* Note: there are other types of potential energy, like elastic, electrical, and chemical. When talking about roller coasters, we usually drop the "gravitational" and just say "potential energy," since it's implied that we aren't talking about the other types.

## Ask an Expert

Curious about the science? Post your question for our scientists.

## For Further Exploration

• Watch your marble closely and observe its speed. Where is the marble going the fastest? Where is it going the slowest?
• Add a straight piece of track to the end of your roller coaster, at the bottom of the loop. How far does the marble roll before friction brings it to a stop?

### Project Ideas

Science Fair Project Idea
This is a really fun project even if you don't like going on roller coasters yourself. You'll build a roller coaster track for marbles using foam pipe insulation and masking tape, and see how much of an initial drop is required to get the marble to "loop the loop." It's a great way to learn about how stored energy (potential energy) is converted into the energy of motion (kinetic energy). Read more
Science Fair Project Idea
If you'd like to investigate the physics of amusement park rides, then this project is for you. You'll build a roller coaster track for marbles using foam pipe insulation and masking tape, and see how much the marble's potential energy at the beginning of the track is converted to kinetic energy at various points along the track. Read more

### Activities

STEM Activity
1
2
3
4
5
820 reviews
Have you ever ridden a roller coaster? Have you ever wanted to design your own? There are plenty of expensive toys and even video games that will let you build your own coasters—but in this project you'll make one out of paper and tape, and learn about roller coaster physics along the way! Read more

### Careers

Career Profile
Mechanical engineers are part of your everyday life, designing the spoon you used to eat your breakfast, your breakfast's packaging, the flip-top cap on your toothpaste tube, the zipper on your jacket, the car, bike, or bus you took to school, the chair you sat in, the door handle you grasped and the hinges it opened on, and the ballpoint pen you used to take your test. Virtually every object that you see around you has passed through the hands of a mechanical engineer. Consequently, their… Read more
Career Profile
You use mechanical devices every day—to zip and snap your clothing, open doors, refrigerate and cook your food, get clean water, heat your home, play music, surf the Internet, travel around, and even to brush your teeth. Virtually every object that you see around has been mechanically engineered or designed at some point, requiring the skills of mechanical engineering technicians to create drawings of the product, or to build and test models of the product to find the best design. Read more
Career Profile
Physicists have a big goal in mind—to understand the nature of the entire universe and everything in it! To reach that goal, they observe and measure natural events seen on Earth and in the universe, and then develop theories, using mathematics, to explain why those phenomena occur. Physicists take on the challenge of explaining events that happen on the grandest scale imaginable to those that happen at the level of the smallest atomic particles. Their theories are then applied to… Read more
Top
Free science fair projects.