Stressed Out? Take a Break with this Project!
AbstractIs an I-beam as strong as a solid beam of the same size? What if you include weight in the comparison: which beam has the greater strength-to-weight ratio? Would an I-beam be stronger than a solid rectangular beam of the same weight? What about other structural shapes (e.g., T-beams, U-beams)? In this project you can find out by setting up a test stand, putting on your safety goggles and measuring how much stress these building components can handle before they snap.
Areas of Science
Short (2-5 days)
Low ($20 - $50)
Minor injury possible: Wear safety glasses when testing beam capacity. Keep hands and feet clear of the area underneath the weight bucket, which may fall at any time.
Andrew Olson, Ph.D., Science Buddies
- How do you choose which material to use for a particular purpose?
- How do you know that manufactured materials meet the advertised specifications?
- How do you know that the finished products have been fabricated properly?
- How long will the finished product last?
- For research and development of new materials, how do you measure progress?
Terms and ConceptsTo do this project, you should do research that enables you to understand the following terms and concepts:
- strength-to-weight ratio.
- What is the difference between compressive stress and tensile stress?
- When you hang a weight from the center of a beam which is supported at both ends, what stress(es) do you induce on the beam, and where?
- Which cross-sectional shape do you expect to be strongest? Weakest?
- Which cross-sectional shape do you expect to have the best strength-to-weight ratio?
- A good place to start is this Science Buddies resource written by Stanford Mechanical Engineering Professor Beth Pruitt and her students:
Stress, Strain and Strength.
- This PBS website has great information on structural engineering, including online labs where you can learn about forces, materials, loads and structural shapes:
WGBH, 2001. "Building Big: Bridges, Domes, Skyscrapers, Dams and Tunnels," PBS Online [accessed February 17, 2004] http://www.pbs.org/wgbh/buildingbig/index.html.
Materials and Equipment
- Safety glasses; available at hardware stores or from online suppliers such as Carolina Biological Supply Company
- At least 15 15-inch lengths of polystyrene (or ABS) plastic structural beams:
- 3 samples each of 5 different cross-sectional shapes
- Plastic beams are sold under the brand name "Plastruct"
- A web search for Plastruct will turn up the company site, where you can find a list of local retailers
- You can also locate many online suppliers
- Sturdy "S" hook (for hanging weight bucket)
- 5 gal plastic bucket
- Weights (water, sand, bricks)
- Postal scale (for weighing beams)
- Bathroom scale
- Test stand, consists of:
- Two supports at equal height, with a gap (about 12 in) between them
- 2 "C" clamps (one for each end of the beam); available from hardware stores or online suppliers such as Carolina Biological Supply Company
Disclaimer: Science Buddies participates in affiliate programs with Home Science Tools, Amazon.com, Carolina Biological, and Jameco Electronics. Proceeds from the affiliate programs help support Science Buddies, a 501(c)(3) public charity, and keep our resources free for everyone. Our top priority is student learning. If you have any comments (positive or negative) related to purchases you've made for science projects from recommendations on our site, please let us know. Write to us at firstname.lastname@example.org.
- Safety note: Wear safety glasses when testing beam capacity. Keep hands and feet clear of the area underneath the weight bucket, which may fall at any time.
- Do your background research and make sure that you understand the terms and concept and can answer the questions above.
- Set up your test stand for supporting the plastic beams. You will want a gap of about one foot, and you will need to clamp each end of the beam firmly in place with a "C" clamp across this gap. You could use a space between two workbenches, or you could build a sturdy frame with pieces of 2×4 and cross-bracing. Your test stand will need to be tall enough to hang a 5-gallon bucket from the beam, plus about 25–30 cm.
- For hanging weight from the beams, get a sturdy S-hook from the hardware store, and hang a 5 gallon plastic bucket from it by the handle.
- For weight, try water (up to 18 kg/bucket), sand (up to 29 kg/bucket for dry sand, 35 kg/bucket for wet sand), or iron weights from a weight-lifting set (somewhere in the range of 70–140 kg/bucket, depending on air space).
- Weigh each beam before testing.
- Clamp each end of the beam down firmly with "C" clamps.
- Test at least 5 different beam shapes.
- Test at least 3 beams of each shape (5 or more is better).
- Add weight bucket (in small, measured increments) until the beam breaks. Weigh the bucket on the bathroom scale to see how much weight was required to break the beam. Record the amount of weight needed to break each beam.
- Watch carefully and record any observations in your lab notebook. Does breakage consistently start in a particular location on all of the beams of a particular type?
- Calculate the strength/weight ratio for each beam, and the average for each cross-sectional shape of beam.
- Graph your results.
- From your observations and measurements, is polystyrene ductile or brittle?
- From your observations of each beam failure, do the various beam shapes perform better, worse or about the same under compression vs. tension?
Ask an Expert
Do you have specific questions about your science project? Our team of volunteer scientists can help. Our Experts won't do the work for you, but they will make suggestions, offer guidance, and help you troubleshoot.
- For a more basic project, see: Strength in Numbers?.
- Orientation of the beam. For beams with asymmetric cross-sections, does the orientation of the beam affect its weight-bearing capacity?
- Hobby shops also sell similar structural parts made of other materials, including wood (various types), ABS plastic, brass and aluminum. Select structural parts with similar dimensions and cross-sections, but made of different materials. Test them with similar methods. Compare the strengths (and weaknesses) of the various materials.
- Measure the vertical deflection of each beam as you add more weight. Remove the weight and see if the material recovers its original shape (elastic deformation) or remains permanently deformed (plastic deformation). Use the additional information to create a stress-strain plot for each type of beam.
- Devise a method for applying and measuring a torque stress to a beam. Test different beam types for resistance to this type of stress.
If you like this project, you might enjoy exploring these related careers:
Cite This PageGeneral citation information is provided here. Be sure to check the formatting, including capitalization, for the method you are using and update your citation, as needed.
Science Buddies Staff. "Stressed Out? Take a Break with this Project!" Science Buddies, 20 Nov. 2020, https://www.sciencebuddies.org/science-fair-projects/project-ideas/MatlSci_p011/materials-science/how-things-break?from=Home. Accessed 31 Mar. 2023.
Science Buddies Staff. (2020, November 20). Stressed Out? Take a Break with this Project! Retrieved from https://www.sciencebuddies.org/science-fair-projects/project-ideas/MatlSci_p011/materials-science/how-things-break?from=Home
Last edit date: 2020-11-20
Explore Our Science Videos
Solubility Science – STEM Activity
Build a Wind-Powered Car
Can you solve this air pressure puzzle?