Jump to main content

Gear Up Your Candy


Active Time
20-30 minutes
Total Project Time
30-45 minutes
Key Concepts
Gears, mechanics
Sabine De Brabandere, PhD, Science Buddies


Did you know that gears are all around you? You can find them in wind-up toys, bicycles, carousels, cars and trucks, cranes, drills, wind turbines, analog watches, and so forth! If you've looked closely at a moving bicycle, you have seen gears at work. Are you curious about their purpose? In this activity you will use candy to make gears and explore why they are so versatile.

This activity is not recommended for use as a science fair project. Good science fair projects have a stronger focus on controlling variables, taking accurate measurements, and analyzing data. To find a science fair project that is just right for you, browse our library of over 1,200 Science Fair Project Ideas or use the Topic Selection Wizard to get a personalized project recommendation.


  • At least two round plastic or cardboard lids of different sizes. Lids with diameters of about 5 centimeters and 12 cm work well.
  • Scissors or utility knife
  • At least 15 individual candies all of the same type, such as spice drops, candy corn or gumdrops
  • Large piece of scrap paper
  • Glue (a hot-glue gun works well)
  • At least two brads, one for each gear you like to make
  • Piece of cardboard or poster board, at least 20-by-30 cm
  • Permanent marker
  • Ruler
  • Adult helper
  • Optional: A lid with diameter of about 18 cm or more lids, they can be identical in size

Prep Work

  1. Start with the larger of your two container lids (for instance, 12 cm) to make the disk of your first gear.
  2. Locate the center of the lid. (Take your time locating the center as this is important to making the gears turn smoothly.)
  3. Ask an adult to carefully make a small hole in the center of the lid with the scissors or utility knife. Put a brad in the hole, and test whether or not the disk turns freely around the brad. If not, make the hole a little larger and test again.
  4. Arrange an even number of candies around the rim of the lid with the base of each candy touching the disk. The candies should be close together and have no more than a few millimeters of space between them.

  5. Remove every other candy. This will leave space for the candies (the teeth of the gear) to mesh with candies on another gear.
  6. Mark the rim of the lid with a dot for each candy so you can remember where to glue them on.

  7. Lay your lid flat side-down on a piece of scrap paper. Glue the candies to the lid so their sides touch the paper (have an adult help if using a hot glue gun). This ensures the candies, when glued on, form a flat plane.

  8. Let the glue dry while you repeat this process with the smaller of the first two lids. Prepare at least two lids of different sizes before starting the activity. You can make more later.
  9. Ensure that the glue is dry and the candies are stable before you start the next steps.


  1. Have an adult help in making a small hole near the middle of your cardboard or poster board. You will use this hole to attach the smaller of the two gears you prepared to the cardboard.
  2. Thread a brad through the hole in the smaller gear and then through the hole in the cardboard. Bend its arms so the disk is fixed to the board. Test if the disk turns freely around the brad and make adjustments where needed.
  3. Place the larger gear to the left of the smaller one so one tooth of the smaller gear is interlocked between two teeth of the larger gear. Let the tooth of one gear reach close to the rim of the other gear but not quite touching (just a couple millimeters away from the rim).

  4. Mark that location of the center of the larger gear on the cardboard, and have an adult help make a hole there.
  5. Attach the larger gear to the cardboard with a brad.
    Think about:
    What do you think will happen when you turn one of these gears?
  6. Try it out!
    Think about:
    What happens when you turn one gear? What about turning the other gear?
  7. Now try turning the other gear.
    Think about:
    Was your prediction correct? Can you tell which gear turned the fastest?
  8. To make it easier for you to see how fast the gears turn, use the marker to draw a line connecting the center of these two gears.

  9. Turn the smaller gear until it completes one full rotation.
    Think about:
    How far did the larger gear move? Did it make more than, less than or exactly one complete turn? Can you tell now which gear turned faster? Why would that happen?
  10. Turn the gears some more.
    Think about:
    Do you notice in which direction the gears turn? Do both turn in the same direction or in opposite directions? Why would that happen?
  11. Optional: Use a container lid with a bigger diameter than the two you used so far to make an even larger gear. Attach it to the right of the set of gears you have so the teeth mesh.
    Think about:
    What do you think will happen if you turn one gear of this set? Can you tell which gear will turn the fastest and which will turn the slowest? Can you predict the direction in which the other two gears will move when you make one turn?

What Happened?

You probably noticed that the smaller a gear is, the faster it rotates. This happens because smaller gears have fewer teeth. Did you also notice that the direction of rotation is the reverse of the other gear when the gears mesh?

Smaller gears have fewer teeth and thus, compared with larger gears, they rotate through fewer teeth before finishing a full rotation. This allows them to turn faster. Take the example of a gear with twelve teeth interlocking with a gear with six teeth. The gear with twelve teeth turns half as fast because it has twice the number of teeth. The interlocking mechanism guarantees that the same number of teeth pass the point where they mesh. When one gear turns over six teeth the other will turn over six teeth as well. When the gear with six teeth makes a full turn the second gear only shifts over six of its twelve teeth. It only makes half a turn and so it rotates half as fast.

Digging Deeper

A gear is a special type of wheel. It is a disk that has teeth, called cogs, around its edge. Most of the time the teeth of two gears interlock, making the two wheels turn together. Sometimes the teeth mesh with a chain that connects the gears. You have probably seen this setup in bicycles.

Gears make tasks easier for humans and for motors. In many machines humans or motors make an axle (a rod that runs through a wheel or gear) turn, and the right gears can make the turning more efficient.

Choosing the right combination of gears is the key to efficient work. Some bikes allow you to choose gears. Depending on the choice the chain will connect different sizes of gears, giving the rider many options for power and efficiency. It allows the rider to conquer a steep hill or move at a fast speed when going downhill—all with the same bike. Wondering how? When riding a bicycle, the rider pushes on the pedals to rotate a small gear. A chain transfers this rotation to another gear that is attached to the back wheel. If the gears are the same size, one rotation of the pedals turns the back wheel once. However, depending on the bicycle and the rider's choice, the chain might connect gears of different sizes. The type of gear chosen determines how many times the back wheel will turn with one rotation of the pedals. This is helpful because a person's capacity in making the peddles turn fast is limited by how fast the rider can move his or her legs. With the help of gears, this no longer limits the speed at which the back wheel rotates. It sounds wonderful to gain speed, but what is gained in speed is lost in power. When the gears are set to transfer one rotation of the pedals to multiple rotations of the back wheel, the rider has to push much harder. Because of this, connecting a larger-sized gear in the front with a small-sized one in the back is a great choice when you are riding downhill but a useless option when riding up a hill. Having a range of gears allows cyclists to adjust their bicycles to the circumstances they are riding in.

Gears made from plastic lids and gumdrops
icon scientific method

Ask an Expert

Curious about the science? Post your question for our scientists.

For Further Exploration

  • Count the number of teeth on a set of interlocking gears and use these numbers to find out how much faster a larger gear rotates when it meshes with a smaller one.
  • Make more gears of different and equal sizes and try different combinations.
  • The gears in this activity were all attached to a flat piece of cardboard. Can you make a configuration where one gear is at a right angle with a second gear?
    Four interlocking gears made from plastic lids and gumdrops
  • The axle is the rod that goes through the middle of a gear. The gears you made in this activity rotate around their axles. Sometimes the gears are fixed to their axle, and the axle turns. Can you make a system where at least one gear is fixed to an axle? What happens if you glue gears of different sizes to the same axle? When could a configuration like that be helpful?
  • Find tools and machines around your home and neighborhood that have gears. Can you find out why gears are used in this tool?

Project Ideas

Science Fair Project Idea
Music boxes, bicycles, and clocks all have one thing in common: GEARS! You might say that gears make the world turn, since they are in so many mechanical instruments. How do they work and how do you know which gears to use? Find out in this simple experiment. Read more
Science Fair Project Idea
Are you into cycling and speed? Then this is the science fair project for you! In this science fair project, you will determine the best gear ratio for your bike, to get the highest speed after a curve and onto a straightaway. You will learn a lot about applied mechanics and gears, all while having fun riding your bike. Read more
Science Fair Project Idea
Have you ever tried to pull out a nail out of wood with your bare hands? Or have you tried to shove a staple through a stack of papers without a stapler? A hammer's claw, a stapler, a pair of pliers and a shovel are each examples of everyday tools that use levers to make our work easier. Read more
Science Fair Project Idea
Did you know that you can lift an object that's heavier than you are? Just use a lever! In this science project you'll build a tabletop lever and measure how much effort it takes to lift an object using it. Read more


STEM Activity
9 reviews
Have you ever wished you could copy a drawing but make it larger or smaller? If you've tried to create a larger or smaller copy of your work, you've probably realized that it is very hard to get the details right. A machine called a pantograph, however, could help. It makes copies that can be scaled up or down or made the same size. In this activity you will make your own pantograph and then duplicate your drawings. Can you figure out how it enlarges, shrinks or turns drawings upside down? Read more



Career Profile
Mechanical engineers are part of your everyday life, designing the spoon you used to eat your breakfast, your breakfast's packaging, the flip-top cap on your toothpaste tube, the zipper on your jacket, the car, bike, or bus you took to school, the chair you sat in, the door handle you grasped and the hinges it opened on, and the ballpoint pen you used to take your test. Virtually every object that you see around you has passed through the hands of a mechanical engineer. Consequently, their… Read more
Career Profile
You use mechanical devices every day—to zip and snap your clothing, open doors, refrigerate and cook your food, get clean water, heat your home, play music, surf the Internet, travel around, and even to brush your teeth. Virtually every object that you see around has been mechanically engineered or designed at some point, requiring the skills of mechanical engineering technicians to create drawings of the product, or to build and test models of the product to find the best design. Read more
Career Profile
Cars are an important part of our daily lives. We depend on them to perform everyday tasks—getting to and from school and work, sports practice, grocery shopping, and various errands—and also to keep us safe while doing so. Our cars can keep us cool or warm while we drive them, and they even help us find our way. The automobile is made up of complicated braking, steering, and electrical systems, in addition to the engine and drive train. All of these systems require a tremendous… Read more
Career Profile
There are so many different types of cars and trucks on the road: sports cars, sport utility vehicles (SUVs), pickup trucks, and even electric vehicles and hybrids. Have you ever wondered how they work? And, how to keep them running? How does the engine make a car's wheels turn? Why does pushing the brake pedal make a car stop? Automotive service technicians (also called mechanics) can pop open the hoods of these different types of cars and answer these questions. Automotive technicians know… Read more
Free science fair projects.